Solo Shower Enclosure, Base & Wall Kit SHOWER ENCLOSURE, SHOWER BASE AND BACKWALLS KIT INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserv
“SOLO” Enclosure Rev.1 Ver.1 05/2013 9 12. Apply the sealant along the profiles and guide rails; on the seams between the bottom guide rail and t
SLIMLINE SHOWER BASE SHOWER BASE DIMENSIONS AND INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign
“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 2Preparation 1. Examine boxes and packages for shipping damage. Carefully remove Shower base from th
“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 3SINGLE THRESHOLD SHOWER BASE Center Drain Configuration MODEL SPECIFICATION D (in) W (in)
“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 4Left-Hand Drain Configuration MODEL SPECIFICAT
“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 5Right-Hand Drain Configuration
“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 6NEO SHOWER BASE MODEL SPECIFICATION W (in) A (in) B (in) C (in) DLT-2
“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 7QUARTER ROUND SHOWER BASE MODEL SPECIFICATION W (in) C (
“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 8DOUBLE THRESHOLD SHOWER BASE Corner Drain Configuration MODEL SPECIFICATION W (in) C
“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 9Left-Hand Drain Configuration MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in)
SOLO SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign products at any time without
“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 10Right-Hand Drain Configuration MODEL SPECIFICATION D (in) W (in) D1 (in)
“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 11Diagram of the Shower Base in a Cross Section Finished Wall Cement board S
“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 12Shower Base Installation Preparation 1. Ensure that the floor and the studs are at right angle. Pr
“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 132. Install the shower drain (NOT PROVIDED) according to the drain installation manual (supplied wit
“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 14 4. Level the tray and place marks on the studs above the upper edge of the tile flange. See
“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 15 6. After the bedding material has been poured and before it sets, place the shower base into the p
“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 16 Fig. 9 Product maintenance To insure long lasting life
Ver. 1, Rev. 1 QWALL – 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign produc
Ver. 1, Rev. 1 2Preparation 1. After opening all boxes and packages, read this introduction carefully. Check that all of the needed parts are inclu
Ver. 1, Rev. 1 3Detailed Diagram of Acrylic Shower Wall Components 56784213 Packing List 01 Side panel 2pcs 05 Glass shelf 2pcs 02 Corner cover
“SOLO” Enclosure Rev.1 Ver.1 05/2013 2Preparation 1. After opening all boxes and packages, read this introduction carefully. Check that all of
Ver. 1, Rev. 1 4Preparation for Installation of Side Panel ATTENTION: See Fig. 1 for details. Fig. 1 1. Place a mark on the
Ver. 1, Rev. 1 5 2. Measure the walls of the shower from the 1” (one inch) line in the corner (from Step. 1) to the points where you want Side panels
Ver. 1, Rev. 1 6 4. Place the Side panel (01) on a flat piece of plywood or particle board. Use a sharp industrial knife and a T-square to score alon
Ver. 1, Rev. 1 7 5. Take exact measurements of the fixture on the wall: • from the 1” (one inch) line in the corner of the shower to the fixture:
Ver. 1, Rev. 1 8 7. Drill the holes for the fixtures in the Side panel (01) using the proper diameter saw bit or a handheld jig saw. See Fig. 9 for
Ver. 1, Rev. 1 9 Fig. 11 9. Mount the Corner cover (02) to the corner of the shower using the Countersunk screws ST4.2×3
Ver. 1, Rev. 1 10 Fig. 13 10. Apply the sealant to the entire surface of the reverse side of the Side panel (01). Also, ap
Ver. 1, Rev. 1 11 11. Slide the narrow edge of the Side panel (01) behind the Corner cover (02). Align trimmed edge of the Side panel (from Step. 4) w
Ver. 1, Rev. 1 12 14. Once Side panels (01) aligned, fasten tight the Corner cover (02) to secure the Side panels. Cover the screw holes with the Dec
Ver. 1, Rev. 1 13 16. Apply caulk along the top edge of the Side panels (01) and along the connection of the bottom edges of the Side panels with the
“SOLO” Enclosure Rev.1 Ver.1 05/2013 3Detailed Diagram of Shower Enclosure Components 1116178910121314151234567 Packing List 01 Wall profile
Ver. 1, Rev. 1 14 18. Mark the location for the Shelf brackets (04) according to the measurements in Fig. 20 and Fig. 21.1. Drill the holes using Ø5/1
Ver. 1, Rev. 1 15 Fig. 23 Product maintenance To insure long lasting life for your acrylic back walls, wipe them off afte
DREAMLINE™EXCLUSIVELIMITEDWARRANTYASOFMAY6,2013Thiswarrantyextendsonlytotheoriginalowner/end‐userforhouseholduseonlyandisnottr
TEL: 866-731-2244 FAX: 866-227-1533 WWW.BATHAUTHORITY.COM For more information on DreamLineTM Shower Doors please visit www.Bath
“SOLO” Enclosure Rev.1 Ver.1 05/2013 4Shower Enclosure Installation 1. Fasten the bottom Guide rail (03) to the Glass profiles (02) with the Ro
“SOLO” Enclosure Rev.1 Ver.1 05/2013 5 3. Repeat Step #1 and Step #2 to fasten the upper Guide rail (03) to the Glass profiles (02) and secur
“SOLO” Enclosure Rev.1 Ver.1 05/2013 6 6. Move the finished frame to the designated position on the shower base, the bathtub or the threshold (d
“SOLO” Enclosure Rev.1 Ver.1 05/2013 7 8. Fasten the top and the bottom Wheel assemblies (17) to the Glass door (06). The top wheels can adjust
“SOLO” Enclosure Rev.1 Ver.1 05/2013 8 10. Install the Handle (07) to the Glass door (06). Press the Anti-water strips (08) on the vertical edges
Comments to this Manuals