DreamLine DL-6442L-01CL Installation Guide

Mirage Shower Door & Base Kit SHOWER Door AND SHOWER BASE KIT INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, mo

“MIRAGE - 48” Rev. 2 Ver. 4 07/2013 9 NOTE: Please refer to Sliding bracket assembly (09) diagram on Page 4. 9. Disassemble the Slid

“MIRAGE - 48” Rev. 2 Ver. 4 07/2013 10 10. Install the Stopper block (11) on the bottom of the Glass door (02). See fig. 11 for deta

“MIRAGE - 48” Rev. 2 Ver. 4 07/2013 11 NOTE: Please refer to Sliding bracket assembly (09) diagram on Page 4. 12. Place the Slider (C

“MIRAGE - 48” Rev. 2 Ver. 4 07/2013 12 13. Press the Bumper strip (14) on the vertical edge of the Glass door (02). Push the Seal gas

“MIRAGE - 48” Rev. 2 Ver. 4 07/2013 13 15. Locate the Support bar (05) and temporarily fasten it to the Sliding bracket assembly (09)

“MIRAGE - 48” Rev. 2 Ver. 4 07/2013 14 NOTICE: The above installation steps are given for the right-hand configuration. For left-hand

SLIMLINE SHOWER BASE SHOWER BASE DIMENSIONS AND INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 2Preparation 1. Examine boxes and packages for shipping damage. Carefully remove Shower base from th

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 3SINGLE THRESHOLD SHOWER BASE Center Drain Configuration MODEL SPECIFICATION D (in) W (in)

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 4Left-Hand Drain Configuration MODEL SPECIFICAT

MIRAGE SHOWER DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign products at any time without pri

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 5Right-Hand Drain Configuration

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 6NEO SHOWER BASE MODEL SPECIFICATION W (in) A (in) B (in) C (in) DLT-2

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 7QUARTER ROUND SHOWER BASE MODEL SPECIFICATION W (in) C (

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 8DOUBLE THRESHOLD SHOWER BASE Corner Drain Configuration MODEL SPECIFICATION W (in) C

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 9Left-Hand Drain Configuration MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in)

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 10Right-Hand Drain Configuration MODEL SPECIFICATION D (in) W (in) D1 (in)

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 11Diagram of the Shower Base in a Cross Section Finished Wall Cement board S

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 12Shower Base Installation Preparation 1. Ensure that the floor and the studs are at right angle. Pr

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 132. Install the shower drain (NOT PROVIDED) according to the drain installation manual (supplied wit

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 14 4. Level the tray and place marks on the studs above the upper edge of the tile flange. See

“MIRAGE - 48” Rev. 2 Ver. 4 07/2013 2 Preparation 1. After opening all boxes and packages, read this introduction carefully. Check t

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 15 6. After the bedding material has been poured and before it sets, place the shower base into the p

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 16 Fig. 9 Product maintenance To insure long lasting life

DREAMLINE™EXCLUSIVELIMITEDWARRANTYASOFMAY6,2013Thiswarrantyextendsonlytotheoriginalowner/end‐userforhouseholduseonlyandisnottr

TEL: 866-731-2244 FAX: 866-227-1533 WWW.BATHAUTHORITY.COM For more information on DreamLineTM Shower Doors please visit www.Bath

“MIRAGE - 48” Rev. 2 Ver. 4 07/2013 3 Detailed Diagram of Shower Door Components 16678910111214131515234 Parts List 01 Stationary gl

“MIRAGE - 48” Rev. 2 Ver. 4 07/2013 4 Sliding Bracket Assembly A Face Plate 1pc F Head screw M4×10 2pcs B Back Pla

“MIRAGE - 48” Rev. 2 Ver. 4 07/2013 5 Shower/Tub Door Installation NOTE: The installation of this door requires two installers. NOTE:

“MIRAGE - 48” Rev. 2 Ver. 4 07/2013 6 3. Fasten the Guide rail connector (08) to one of the sides of the Guide rail (03). Slide in tw

“MIRAGE - 48” Rev. 2 Ver. 4 07/2013 7 5. Mount the Wall bracket (12) to Stationary glass (01). Slide the glass into the channel of th

“MIRAGE - 48” Rev. 2 Ver. 4 07/2013 8 7. Outline the position of the Wall bracket (12) on the wall. Set Stationary glass (01) aside.