DreamLine SHEN-60367212-08 Installation Guide

ENIGMA SHOWER ECLOSURE INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign products at any time wit

“ ENIGMA” Enclosure Rev. 3 Ver.4 04/2013 10 10. Mark the drilling holes on the floor through the predrilled holes in the Threshold (15). Remove t

“ ENIGMA” Enclosure Rev. 3 Ver.4 04/2013 11If the width of your door is 72” and you are installing the door with the Small Stationary glass (24),

“ ENIGMA” Enclosure Rev. 3 Ver.4 04/2013 12 13. Make sure the Stationary glass (02) and the Guide rail (03) are leveled. If a horizontal adjustme

“ ENIGMA” Enclosure Rev. 3 Ver.4 04/2013 13 15. Apply a small amount of silicone into the Threshold (15) channel. Place the Stationary glass (02)

“ ENIGMA” Enclosure Rev. 3 Ver.4 04/2013 14 ATTENTION: This Step shows Small Stationary Glass (24) installation for 72” door only. 16. Screw of

“ ENIGMA” Enclosure Rev. 3 Ver.4 04/2013 15 17. A. Measure the distance between the Stationary glass (02) and the Return panel (22) for 60” door

“ ENIGMA” Enclosure Rev. 3 Ver.4 04/2013 16 19. Attach two top Rollers (04) to the Glass door (05). Suspend the door by hanging the Rollers onto

“ ENIGMA” Enclosure Rev. 3 Ver.4 04/2013 17 21. Press the Bumper strip (13) on the vertical edge of the Glass door (05) and also press the Anti

“ ENIGMA” Enclosure Rev. 3 Ver.4 04/2013 18 23. Apply silicone along the connection of the Stationary glasses to the wall. You may also apply add

DREAMLINE™EXCLUSIVELIMITEDWARRANTYASOFMAY6,2013Thiswarrantyextendsonlytotheoriginalowner/end‐userforhouseholduseonlyandis nott

“ ENIGMA” Enclosure Rev. 3 Ver.4 04/2013 2Preparation 1. After opening all boxes and packages, read this introduction carefully. Check that all

TEL: 866-731-2244 FAX: 866-227-1533 WWW.BATHAUTHORITY.COM For more information on DreamLineTM Shower Enclosures please visit www.

“ ENIGMA” Enclosure Rev. 3 Ver.4 04/2013 3Detailed Diagram of Shower Enclosure Components Diagram A Diagr

“ ENIGMA” Enclosure Rev. 3 Ver.4 04/2013 4Shower Enclosure Plan NOTICE: The Guide rail (03) and the Threshold (15) has been precut for the

“ ENIGMA” Enclosure Rev. 3 Ver.4 04/2013 5Shower Enclosure Installation 1. Attach the Wall brackets (19) to the Return glass panel (22). Bolte

“ ENIGMA” Enclosure Rev. 3 Ver.4 04/2013 6 2. Position the Return panel (22) on desirable distance from the side wall. This distance is marked

“ ENIGMA” Enclosure Rev. 3 Ver.4 04/2013 7 4. Drill the holes in the wall and the floor using Ø 5/16” drill bit and insert the Wall anchors (18)

“ ENIGMA” Enclosure Rev. 3 Ver.4 04/2013 8 6. According to desirable distance “W” between the wall and the internal side of the Return panel (22

“ ENIGMA” Enclosure Rev. 3 Ver.4 04/2013 98. Your Threshold (15) has been precut for your Shower model opening width: 60” or 72” for shower widt