QWALL – 4 & SlimLine Shower Base Kit ACRYLIC SHOWER WALL AND SHOWER BASE KIT INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the righ
Ver. 1, Rev. 1 9 Fig. 11 9. Mount the Corner cover (02) to the corner of the shower using the Countersunk screws ST4.2×3
Ver. 1, Rev. 1 10 Fig. 13 10. Apply the sealant to the entire surface of the reverse side of the Side panel (01). Also, ap
Ver. 1, Rev. 1 11 11. Slide the narrow edge of the Side panel (01) behind the Corner cover (02). Align trimmed edge of the Side panel (from Step. 4) w
Ver. 1, Rev. 1 12 14. Once Side panels (01) aligned, fasten tight the Corner cover (02) to secure the Side panels. Cover the screw holes with the Dec
Ver. 1, Rev. 1 13 16. Apply caulk along the top edge of the Side panels (01) and along the connection of the bottom edges of the Side panels with the
Ver. 1, Rev. 1 14 18. Mark the location for the Shelf brackets (04) according to the measurements in Fig. 20 and Fig. 21.1. Drill the holes using Ø5/1
Ver. 1, Rev. 1 15 Fig. 23 Product maintenance To insure long lasting life for your acrylic back walls, wipe them off afte
SLIMLINE SHOWER BASE SHOWER BASE DIMENSIONS AND INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign
“SLIMLINE SHOWER BASE” Rev.3 Ver.4 05/2013 2Preparation 1. Examine boxes and packages for shipping damage. Carefully remove Shower base from th
“SLIMLINE SHOWER BASE” Rev.3 Ver.4 05/2013 3SINGLE THRESHOLD SHOWER BASE Center Drain Configuration MODEL SPECIFICATION D (in) W (in)
Ver. 1, Rev. 1 QWALL – 4 ACRYLIC SHOWER WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign produc
“SLIMLINE SHOWER BASE” Rev.3 Ver.4 05/2013 4Left-Hand Drain Configuration MODEL SPECIFICAT
“SLIMLINE SHOWER BASE” Rev.3 Ver.4 05/2013 5Right-Hand Drain Configuration
“SLIMLINE SHOWER BASE” Rev.3 Ver.4 05/2013 6NEO SHOWER BASE MODEL SPECIFICATION W (in) A (in) B (in) C (in) DLT-2
“SLIMLINE SHOWER BASE” Rev.3 Ver.4 05/2013 7QUARTER ROUND SHOWER BASE MODEL SPECIFICATION W (in) C (
“SLIMLINE SHOWER BASE” Rev.3 Ver.4 05/2013 8DOUBLE THRESHOLD SHOWER BASE Corner Drain Configuration MODEL SPECIFICATION W (in) C
“SLIMLINE SHOWER BASE” Rev.3 Ver.4 05/2013 9Left-Hand Drain Configuration MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in)
“SLIMLINE SHOWER BASE” Rev.3 Ver.4 05/2013 10Right-Hand Drain Configuration MODEL SPECIFICATION D (in) W (in) D1 (in)
“SLIMLINE SHOWER BASE” Rev.3 Ver.4 05/2013 11Diagram of the Shower Base in a Cross Section Finished Wall Cement board S
“SLIMLINE SHOWER BASE” Rev.3 Ver.4 05/2013 12Shower Base Installation Preparation 1. Ensure that the floor and the studs are at right angle. Pr
“SLIMLINE SHOWER BASE” Rev.3 Ver.4 05/2013 132. Install the shower drain (NOT PROVIDED) according to the drain installation manual (supplied wit
Ver. 1, Rev. 1 2Preparation 1. After opening all boxes and packages, read this introduction carefully. Check that all of the needed parts are inclu
“SLIMLINE SHOWER BASE” Rev.3 Ver.4 05/2013 14 4. Level the tray and place marks on the studs above the upper edge of the tile flange. See
“SLIMLINE SHOWER BASE” Rev.3 Ver.4 05/2013 15 6. After the bedding material has been poured and before it sets, place the shower base into the p
“SLIMLINE SHOWER BASE” Rev.3 Ver.4 05/2013 16 Fig. 9 Product maintenance To insure long lasting life
DREAMLINE™EXCLUSIVELIMITEDWARRANTYASOFMAY6,2013Thiswarrantyextendsonlytotheoriginalowner/end‐userforhouseholduseonlyandisnottr
TEL: 866-731-2244 FAX: 866-227-1533 WWW.BATHAUTHORITY.COM For more information on DreamLineTM Shower Bases ple
Ver. 1, Rev. 1 3Detailed Diagram of Acrylic Shower Wall Components 56784213 Packing List 01 Side panel 2pcs 05 Glass shelf 2pcs 02 Corner cover
Ver. 1, Rev. 1 4Preparation for Installation of Side Panel ATTENTION: See Fig. 1 for details. Fig. 1 1. Place a mark on the
Ver. 1, Rev. 1 5 2. Measure the walls of the shower from the 1” (one inch) line in the corner (from Step. 1) to the points where you want Side panels
Ver. 1, Rev. 1 6 4. Place the Side panel (01) on a flat piece of plywood or particle board. Use a sharp industrial knife and a T-square to score alon
Ver. 1, Rev. 1 7 5. Take exact measurements of the fixture on the wall: • from the 1” (one inch) line in the corner of the shower to the fixture:
Ver. 1, Rev. 1 8 7. Drill the holes for the fixtures in the Side panel (01) using the proper diameter saw bit or a handheld jig saw. See Fig. 9 for
Comments to this Manuals